Search
Close this search box.

Structure and Hardware Parameters of Colorlight 5A Products Series

Know about Structure and Hardware Parameters of Colorlight 5A Products such as Colorlight 5A / 5A-F / 5A-75 /5A-75E LED Receiver Carda,LED Control Card.

Hardware figure and parameters

1. 5A and 5AF hardware figure and parameters

1.1 Hardware figure

Hardware figure of Colorlight 5A series

1.2 Hardware interface descriptions

S/N

Name

Function

Remarks

1

Power-in 1

Connect DC5V power supply to power the receiving card.

Only one is used.

2

Power-in 2

Connect DC5V power supply to power the receiving card.

3

Net port A

RJ45, for transmission of network signals

The dual net ports can achieve import/export at random, which can be identified in an intelligent way by the system.

4

Net port B

RJ45, for transmission of network signals

5

Indicator light

It indicates the status of power and signal transmission.

Red for power, green for signals

6

Peripheral ports

For Indicator light and test buttons

Two kinds of interface definitions

7

Relay port

The cabinet fan power can be controlled through the relay.

To be customized

8

Flash

2Gbit memory chips can be soldered to store offline contents

5AF version

9

Dual 50P pins

Connected to all display HUB boards

 

10

Test buttons

The attached test procedures can achieve four kinds of monochrome display (red, green, blue and white), as well as horizontal, vertical and other display scan modes.

 

11

Temperature sensor port

Temperature probes can be soldered to detect the temperature of each card.

To be customized

1) Indicator Light functions
Red: ON for power available
Green: ON/OFF quick flash (about 5-10 times / second) indicates that the data signal transmission is normal. 2) Definitions of 50P pins

Full Color

Function

Note

2, 4, 47, 49

VCC 5V

Power

1, 3, 5, 46, 48, 50

GND

Ground

10, 14, 18, 22, 26, 30, 34, 38

R

Data signal

8, 12, 16, 20, 24, 28, 32, 36

B

9, 13, 17, 21, 25, 29, 33, 37

G

7, 11, 15, 19, 23, 27, 31, 35

RP (red virtual pixel)

45

OE

Control signal

43

LAT

44

CLK

42

A

Scan signal

41

B

40

C

39

D

6

Expansion port

 

Note: The figures in the table above indicate the pin number on the 50P port for receiving card output (The positions of 1, 2, 49 and 50 refer to the marks on Figure 2-2).

 

3) Figure for receiving card size and hole position

size and hole position of Colorlight 5A series card

1.3 Relevant parameters

Voltage: 3-7V Current: 400-600mA
Power: 3W ± 5% Operating temperature: -25 ℃ – +70 ℃

5AS hardware figure and parameters

2   5AS hardware figure and parameters 2.1 5AS hardware figure
Colorlight 5AS hardware chart

2.2 Hardware interface descriptions

S/N

Name

Function

Remarks

1

Net port A

RJ45, for transmission of network signals

The dual net ports can achieve import/export at random, which can be identified in an intelligent way by the system.

2

Net port B

RJ45, for transmission of network signals

3

D5,D6

If D5 is welded but D6 not, the input voltage will be 6V ~ 45V, and if less than 6V, the system does not work; if D6 is welded but D5 not, the input voltage will be 5V, ± 10%, and if too high voltage, the system will be burned.

Only one of the two shall be welded.

4

Power-in

To power the receiving card

 

5

Indicator light

It indicates the status of power and signal transmission.

 

6

Test buttons

The attached test procedures can achieve four kinds of monochrome display (red, green, blue and white), as well as horizontal, vertical and other display scan modes.

 

7

Temperature sensor port

Temperature probes can be soldered.

 

8

Signal output port J2

Two groups of parallel RGB output or 6 groups of serial signals

Only J1 or J2 is to be connected.

9

Signal output port J1

Four groups of parallel data or 16 groups of serial output

 

J1, J2 signal port definitions

signal port definitions of Colorligth 5A series card

Note: J1 and J2 can not be used together. J1 and J2 signals are defined as the first four and two groups of 5A cards respectively. Serial signals or signals in any other form can be achieved by updating the program.

2.3 Relevant parameters

Voltage: 5-45V Current: 400-600m
Power: 3W ± 5% Operating temperature: -25 ℃ – +70 ℃

Hot Selling Products

Contact Us

Our sale team will give full support and price you needed.